Techno And Science News | Rssonmyspace.com

Posts Tagged ‘free’

When studying for your BSCI exam for the CCNP, you get your first taste of BGP. One of the major differences between BGP and the other protocols you’ve studied to date is that BGP uses attributes to describe paths, and to influence the selection of one path over the other.

In this free tutorial, we’re going to take a look at the Local Preference attribute and compare it to the Cisco-proprietary BGP attribute “weight”.

The Local Preference (LOCAL_PREF) attribute is used to influence how traffic will flow from one Autonomous System (AS) to another when multiple paths exist. For example, if AS 100 has two different paths to a destination network in AS 200, the LOCAL_PREF attribute can be used to influence the path selection.

The major difference between the Weight and LOCAL_PREF attributes is that when the LOCAL_PREF attribute is changed, that change is reflected throughout the AS. The new LOCAL_PREF value will be advertised to all other routers in the AS, as compared to the Weight attribute, which is locally significant only. If you change the Weight for a path on one router in an AS, the other routers in the AS will not learn of the change.
Read the rest of this entry »

When you’re studying for your BSCI exam and CCNP certification, you quickly realize that BGP is a whole new world from anything you’ve previously studies. One topic that sometimes confuses CCNP candidates is when a BGP route reflector needs to be configured.

In the following example, the routers R1, R2, and R3 are all in BGP AS 100. This is not a full mesh, however. There are peer relationships between R1-R2 and R1-R3, but not between R2 and R3. R3 is advertising network 3.3.3.0/24 via BGP, and the route is seen on R1. R1′s iBGP neighbor, R2 does not see the route.

A basic rule of BGP is that a BGP speaker cannot advertise a route to an iBGP neighbor if that route was learned from another iBGP neighbor. Configuring R1 as a route reflector will allow us to circumvent this rule. The entire route reflector process is transparent to the clients, and no configuration is necessary on those clients. We’ll configure R1 as a route reflector for both R2 and R3.
Read the rest of this entry »

Configuring RIPv2 and EIGRP authentication with key chains can be tricky at first, and the syntax isn’t exactly easy to remember. But for BSCI and CCNP exam success, we’ve got to be able to perform this task.

In a previous tutorial, we saw how to configure RIPv2 packet authentication, with both clear-text and MD5 authentication schemes. EIGRP authentication is much the same, and has the text and MD5 authentication options as well. But EIGRP being EIGRP, the command just has to be a little more detailed!

As with RIPv2, the authentication mode must be agreed upon by the EIGRP neighbors. If one router’s interface is configured for MD5 authentication and the remote router’s interface is configured for text authentication, the adjacency will fail even if the two interfaces in question are configured to use the same password.

We’ll now configure link authentication on the adjacency over an Ethernet segment. Below, you’ll see how to configure a key chain called EIGRP on both routers, use key number 1, and use the key-string BSCI. Run show key chain on a router to see all key chains.

R2(config)#key chain EIGRP

R2(config-keychain)#key 1

R2(config-keychain-key)#key-string BSCI

R2#show key chain

Key-chain EIGRP:

key 1 — text “BSCI”

accept lifetime (always valid) – (always valid) [valid now]
Read the rest of this entry »

While routers accept and generate broadcasts, they do not forward them. This can be quite a problem when a broadcast needs to get to a device such as a DHCP or TFTP server that’s on one side of a router with other subnets on the other side.

If a PC attempts to locate a DNS server with a broadcast, the broadcast will be stopped by the router and will never get to the DNS server. By configuring the ip helper-address command on the router, UDP broadcasts such as this will be translated into a unicast by the router, making the communication possible. The command should be configured on the interface that will be receiving the broadcasts.

R1(config)#int e0

R1(config-if)#ip helper-address ?

A.B.C.D IP destination address

R1(config-if)#ip helper-address 100.1.1.2

Now, you may be wondering if this command covers all UDP services. Sorry, you’re not getting off that easy! The command does forward eight common UDP service broadcasts, though.

TIME, port 37

TACACS, port 49

DNS, port 53

BOOTP/DHCP Server, port 67

BOOTP/DHCP Client, port 68

TFTP, port 69

NetBIOS name service, port 137

NetBIOS datagram service, port 138

That’s going to cover most scenarios where the ip helper-address command will be useful, but what about those situations where the broadcast you need forwarded is not on this list? You can use the ip forward-protocol command to add any UDP port number to the list.

Additionally, to remove protocols from the default list, use the no ip forward-protocol command. In the following example, we’ll add the Network Time Protocol port to the forwarding list while removing the NetBIOS ports. Remember, you can use IOS Help to get a list of commonly filtered ports!

R1(config)#ip forward-protocol udp ?

<0-65535> Port number

biff Biff (mail notification, comsat, 512)

bootpc Bootstrap Protocol (BOOTP) client (68)

bootps Bootstrap Protocol (BOOTP) server (67)
Read the rest of this entry »